"- Umožňuje připojení SATA zařízení (jako jsou například pevné disky, optické mechaniky) na IDE rozhraní IOI ref.: IDE-SATA07 - pro všechny SATA HDD - bulk - Chip:Marvell 88SA8052 IDE-SATA07 is a Parallel ATA to Serial ATA Host mode Bridge Board featuring Marvell 88SA8052 Serial ATA bridge Controller. IDE-SATA07 is ideally suited for tailgate interface applications for converting Serial ATA device into ATA device. Both ATA and ATAPI modes are supported using the same firmware. Technical Specifications Parallel ATA to Serial ATA Bridge Board: * Serial ATA: o Compliant with Serial ATA 1.0 o 48-bit sector addressing * Serial ATA Connector: o Signal + Power (7+15 pin) Female Type Connector * Parallel ATA: o Ultra ATA/133 Parallel Interface o 48-bit sector addressing o Jumper for selecting Master and Slave * Parallel ATA Connector: o Male IDC 2X20 pin Connector * Transfer Rate: o Supports PIO and DMA modes o Supports bus master DMA at 1.5Gbps burst rate * DC Power Connector: o IDE Big 4-pin power connector * LEDs o Power LED o SATA PHY Ready LED o Activity LED (Pin Header 2pin Pitch=2.54mm) "

 "Specifikace Host Bus: 1-lane 2.5 Gb/s PCI Express Number of Ports: One eSATA and One Internal SATA ports Boot ROM: Non Low Profile PCI Form Factor: Yes Introduction The SATA2-PCIE1x21 is a two ports Serial ATA II to 1-lane 2.5 Gb/s PCI Express Host Adapter. The SATA2-PCIE1x21 is designed to provide two ports Serial ATA II connectivity (Serial ATA Generation 2 transfer rate of 3.0 Gb/s). The SATA2-PCIE1x21 supports both AHCI and Legacy IDE controller to increase system feasibility, including Native Command Queuing (NCQ), hot plugging, ATAPI device supporting, programmable output swing control to fit SATA II Gen2i and Gen2m (External SATA Connection, eSATA). Technical Specification Compliance Compliant with Serial ATA AHCI (Advanced Host Controller Interface) Spec. Revision 1.0 Compliant with Bus Master Programming interface for IDE ATA Controllers Revision 1.0 Compliant with PCI Express Bus Spec. Revision 1.0a Compliant with Serial ATA High Speed Serialized AT Attachment Spec. Revision 1.0a Compliant with Serial ATA II: Extensions to Serial ATA 1.0a Revision 1.1 Compliant with Gen2i and Gen2m Serial ATA II: Electrical Spec. Revision 1.0 PCI Express Features Supports 1-lane 2.5 Gb/s PCI Express Internal native interface to 1-port All registers accessible in unified memory space Supports a slave SMBus interface (follow System Management Bus Specification Revision 1.1) Serial ATA Features Supports Serial ATA Generation 2 transfer rate of 3.0 Gb/s Supports SATA II Gen2i and Gen2m (External SATA Connection, eSATA) Supports Native Command Queuing (NCQ) Supports Hot Plugging Systémové požadavky PC with 1-lane 2.5 Gb/s PCI Express slot Windows 2000/XP and Windows Server 2003 Drivers: Drivers for Windows 2000/XP and Windows Server 2003 /win7 Mac OS 10.4.8 or later (No driver need) Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "The Delock PCI card powered by IOI expands your PC by three external FireWire 400 Ports. You can connect FireWire devices like external enclosure, digital camera, camcorder, etc. to the card. Specification • IOI item number: IOI-4343T • 3x external FireWire IEEE 1394a ports • 1x mini 4pin DC +12 V power connector • IEEE 1394a to PCI controller: Texas Instruments TSB43AB23 • Data transfer rate up to 400 Mb/s • 32-bit PCI standard 2.2 System requirements • Windows 98SE/ME/2000/XP/Vista/7, Mac OS 8.6 or above, Linux 2.4.x • PC with one free PCI Slot Package content • PCI card Package • Box"

 "Specifikace -2-port Serial ATA to PCI Express Host Adapter with Silicon Image Sil3132 Serial ATA Host Controller -PCI Express Card x1 to 2x SATA Ports -Supports 1-lane 2.5 Gb/s PCI Express -Chipset: Silicon Image Sil3132 -Data transfer rate: Serial-ATA 3.0 GB/s -For Windows 2000/XP/2003/ Linux 2.6, Mac OSx Sytémové požadavky -volný PCI Express Slot -Windows 2000/XP/2003/ Linux 2.6, Mac OSx Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "Host Bus: 1-lane 2.5 Gb/s PCI Express Number of Ports: One External & Three Internal SATA ports + One Internal PATA ports Form Factor: Standard Type Boot ROM: Yes Introduction SATA2-PCIE1x12 is a multiple port Serial ATA (SATA)/Parallel ATA (PATA) to PCI Express (PCIE) Host Adapter. SATA2-PCIE1x11 takes advantages of the 2.5 Gb/s burst rate of 1-lane PCI Express bus and the Serial ATA Generation 2 transfer rate of 3.0 Gb/s (300 MB/s) interface. This solution provides full PCI Express and Serial ATA (SATA)/Parallel ATA (PATA) functionality and performance. SATA2-PCIE1x12 delivers the performance and connectivity required for servers and I/O demanding applications such as CD-ROM servers, Video-On-Demand, database servers, workstations, high-end desktops, software RAID sub systems, and image systems. SATA2-PCIE1X12 supports a high reliable and extremely fast variety of storage applications (RAID 0, 1, 10, 5 and JBOD). Technical Specification PCI Express 1.0a compliant - Supports 1-lane 2.5 Gb/s PCI Express interface PCI Express Programming interface Compatibility mode via PCI I/O access for legacy host software Enhanced Mode for SATA ports via Enhanced Mode Registers. Enhanced Mode for PATA port via Enhanced Mode Registers. Supports up to 2Mbit external Flash for option ROM or Boot ROM Supports SPI Flash Interface for retrieving boot code and vendor specific PCI Configuration content. Supports TWSI EEPROM interface for retrieving vendor specific PCI Configuration content. Serial ATA (SATA) specification 2.5 compliant. Supports SATA PHY 3.0 Gb/s with speed negotiation to SATA 1.5Gb/s. Supports electrical specifications of Gen1i, Gen1m, Gen1x, Gen2i, Gen2m, Gen2x, and usage models of eSATA and xSATA Supports four independent Serial ATA ports Serial ATA (SATA) protocols over SATA ports. ATA and ATAPI commands Native Command Queuing (NCQ) Hot Plug Port Multiplier Supports SATA Port Selector Switching Parallel ATA (PATA) protocols over PATA port. Supports one Parallel ATA port ATA and ATAPI commands All modes of PIO, Multiword DMA, and Ultra-DMA (up to 150MB/s) Tagged Command Queuing (TCQ) with 32 outstanding commands per port Master and Slave configuration (over PATA port) Supports interrupt Coalescing over SATA and PATA ports in Enhanced Mode. Supports SMBus for communication with Hardware Monitoring ICs. Computer Platfrom PC with 1-lane 2.5 Gb/s PCI Express slot Operating System Requirements Windows 2000/XP/Windows Server 2003/Vista Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "Specifikace - PCI Express Host Adapter na 3 porty OHCI 1.1 kompatibilní IEEE-1394B - PCI Express x1 - 2+1 FireWire-B porty (2 x externí, 1 x interní) - čipová sada: Agere/LSI FW643 - rychlost přenosu dat: 800Mbps - Bus power konektor: IDE 4-pin DC napájecí konektor - pro Windows 2000/XP, Server2003, MacOS 10.4.8 nebo vyšší, Linux 2.6 - Standard- a LowProfile záslepka slotu součástí dodávky OHCI (Open Host Controller Interface) Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance. OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode. 8 Kbyte isochronous transmit FIFO. 4 Kbyte asynchronous transmit FIFO. 8 Kbyte isochronous receive FIFO. 8 Kbyte asynchronous receive FIFO. Dedicated asynchronous and isochronous descriptor-based DMA engines. Eight isochronous transmit contexts. Eight isochronous receive contexts. Supports parallel processing of incoming physical read and write requests. Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers. 1394b-2002 Link Cycle master and isochronous resource manager capable. Supports 1394a-2000 and 1394b-2002 acceleration features. 1394b-2002 PHY Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper. Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus. Link is not required for hub operation. Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders. Does not require external filter capacitor for PLL. Supports arbitrated short bus reset to improve utiliza-tion of the bus. Supports ack-accelerated arbitration and fly-by concat-enation. Supports PHY pinging and remote PHY access pack-ets. Fully supports suspend/resume. Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V. Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "* Host Bus: 1-lane 2.5 Gb/s PCI Express * Eight (8) isochronous transmit/receive contexts * Deep 8 Kbyte isochronous transmit/receive FIFO’s * Complies with 1394 OHCI draft 1.2 * Three external 1394 ports * Bilingual ports with Screw Holes for Jackscrew Type Plug Cable The FWB-PCIE1X21B combines an OHCI (Open Host Controller Interface) and a high-performance, standards-compliant PCI Express 1.1 host system interface to provide S800 1394b-2002 compliant throughput in a small PCB (Printed Circuit Board) and low power dissipation. MultipleVCs (Virtual Channels) on the PCI Express link provide native support for QoS (Quality of Service) transmission for real-time and multimedia applications in a standards-based framework, ensuring compatibility with current and future operating systems. Active-state power management allows dynamic power management during periods of reduced network activity. Technical Specification PCI Express: * Designed for compliance with PCI Express. * Multiple virtual channel (VC0,VC1 ) support fordiffe-rentiating 1394 isochronous traffic. * Supports eight user-programmable traffic classes. * 64-bit and 32-bit platform support. * Interrupts via legacy INTx interface or message sig-naled interrupt (MSI). * Supports PCI Express clock power management viaCLKREQN signal for form factors that support thisprotocol. * Supports all linkpowermanagement states (L0,L0s,L1,andL2/L3) and active state power management(ASPM). * Supports wake-up from a low-power state via in-bandbeacon signaling and side-band WAKE_N signal. OHCI (Open Host Controller Interface) * Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance. * OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode. * 8 Kbyte isochronous transmit FIFO. * 4 Kbyte asynchronous transmit FIFO. * 8 Kbyte isochronous receive FIFO. * 8 Kbyte asynchronous receive FIFO. * Dedicated asynchronous and isochronous descriptor-based DMA engines. * Eight isochronous transmit contexts. * Eight isochronous receive contexts. * Supports parallel processing of incoming physical read and write requests. * Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers. 1394b-2002 Link * Cycle master and isochronous resource manager capable. * Supports 1394a-2000 and 1394b-2002 acceleration features. 1394b-2002 PHY * Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper. * Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus. * Link is not required for hub operation. * Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders. * Does not require external filter capacitor for PLL. * Supports arbitrated short bus reset to improve utiliza-tion of the bus. * Supports ack-accelerated arbitration and fly-by concat-enation. * Supports PHY pinging and remote PHY access pack-ets. * Fully supports suspend/resume. Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V. Number of Ports: * Three Bilingual P1394b Cable Ports with Screw Holes for Jackscrew Type Plug Cable Bus Power Connector: * Big IDE 4-pin DC Power Connector Operating System Requirements * Windows 2000/XP and Windows Server 2003 * Mac OS 10.4.8 or later * Linux 2.6.X Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "The Delock FireWire PCI card by IOI expands your PC by four external FireWire A ports. You can connect several FireWire devices like e.g. external enclosures with integrated hard disk or CD drive, camcorder etc. to the card. Specification • IOI item number: IOI-4601-22 • 4 x external FireWire A (IEEE 1394a) • 1 x intern Bus power connector with mini 4 Pin DC + 12 V power connector • Chipset: 2 x TI TSB43AB22A • Data transfer rate up to 800 Mb/s (400 Mb/s / Channel) per Port • 32-Bit PCI standard 2.2 • Supports OHCI 1.1 standard • Dual channel OHCI System requirements • Windows 98SE/Me/2000/XP/Server-2003/Vista/7, Mac OS 10.5 or higher, Linux Kernel 2.6 • One free PCI slot Package content • PCI Express Card 4x external FireWire A • Y-cable power Molex > Molex 4 Pin + 31/2 FDD Package • Antistatic cover Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "Specifikace One to Five SATA Port Multiplier (SCSI I 50pin Low Density Centronics Connector Form Factor) Highlight 1-to-5 SATA Port Multiplier Full support for FIS-based switching and command-based switching SATA host controllers Supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation Supports host control of hard disk drive staggered spin-up All ports support hot plug and extended (48 bit LBA) drive capability. ATAPI support Features independent 8 KByte FIFO per Device Serial ATA channel for reads and writes Host and device status and activity LEDs Coupling with SATA2-PCIE02 or SATA2-PCIX01 to support RAID Function (RAID 0, 1, 5, 10, Concatenated and JBOD). SPMH3726 is 1-to-5 SATA Port Multiplier designed to provide a high performance link between a single SATA host port and 5 SATA device ports. With its unique data aggregation capability and 3Gbps serial link capability, the SPMH3726 is able to take full advantage of 3Gbps host link bandwidth and FIS-based switching host controllers by bundling together data from device ports and sending it over the 3Gbps host link. Additionally, the feature-rich SPMH3726 supports all the port multiplier related SATA II extensions allowing system designers to exploit the full potential of SATA in their storage solutions. The SPMH3726 supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation allowing system designers to utilize 3Gbps host links with today??s 1.5Gbps hard drives, and to futureproof designs for the emergence of 3Gbps SATA hard drives. Additionally, the SPMH3726 contains a SATA enclosure management bridge (SEMB) to pass in-band enclosure management information between the host and an enclosure management device. Other important features include, programmable high drive capability for backplane and external applications, asynchronous notification to eliminate the need for host polling to determine if a device has been added or removed, and hot plug support. Coupling with proper host controllers such as Silicon Image Sil3124, Sil3132 and Marvell 88SE6145, SPMH3726 - SATA II port multiplier, a high reliable and extremely fast variety of storage applications (RAID 0, 1, 5, 10, Concatenated and JBOD). MH3726 delivers the performance and connectivity required for servers and I/O demanding applications such as CD-ROM servers, Video-On-Demand (digital content and high-definition video), database servers, workstations, high-end desktops, software RAID sub systems, and image systems. Technical Specification Host Port - Supports one SATA host port, 1.5Gb/s and 3Gb/s - Hot Plug support - Supports Async Notification - SATA Port Multiplier spec. compliant - Supports PM aware hosts and non-PM aware - Two detailed system status LEDs - eSATA signal level suppport (1m and 2m PHY compliant) Device Port - Four SATA device ports, 1.5Gb/s and 3Gb/s - Hot Plug support - SATA Port Multiplier spec. complaint - Compatible with NCQ drives - Two LEDs for detailed status per port - eSATA signal level support (1m and 2m PHY compliant) System Features - Five status LEDs for system functions - Works without BIOS updates - Max. performance greater than 220MB/s (RAID 0) - Enclosure Management SEMB (I2C bus) support - Automatic bad sector remapping - OS Agnostic operation - Bootable arrays and staggered spin-ups - ATAPI device support in PM mode - Spread Spectrum Clocking w/SSC clock - Event logging from GUI - Remote monitoring and management - Email notification - Manage multiple devices via GUI - Field-upgradeable firmware Application Expansion Storage Bricks Disk Shelves Storage Enclosures It is designed to provide a high performance link between a single SATA2 host port and 5 SATA device ports. With its unique data aggregation and 3Gbps serial link capacity, it supports 5 SATA or SATA2 device with auto-negotiation features over one single eSATA connector. SPMH3726 is equipped with a "SCSI I 50pin Low Density Centronics Connector" like bracket to be mounted in a standard enclosure to provide the immediate upgrade of your storage system. Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "3-port OHCI Compliant Firewire 800 (IEEE 1394b) to PCI Host Adapter featuring Ti TSB83AA23 IEEE 1394 Host Controller (Low Profile PCI Form Factor) * 32-bit PCI Host interface * One Internal Bilingual (1394b) Port * Two External Bilingual (1394b) connectors (with screw lock) * Big IDE 4-pin DC Power Connector for supplying power to the 1394 Bus * Low Profile PCI Form Factor FWB-PCI3203 is a three port OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) to PCI Host Adapter featuring Texas Instruments OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) Single Chip Host Controller. Technical Specification Host Bus: * 33-MHz/32-Bit PCI Interface * 3.3-V and 5-V PCI Signaling Environments IEEE 1394 Std Support: * Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates * Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus * Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394 1394 Bus Transfer Rate: Provides three fully backward-compatible, (IEEE Std 1394a-2000 fully compliant) Bilingual IEEE Std 1394b-2002 cable ports at S100/S200/S400/S400B/S800 megabits per second (Mbits/s). IEEE-1394 to PCI Controller Texas Instruments TSB83AA23 DV and DA Enhancement: * Digital Video and Audio performance enhancements. * Extended resume signaling for compatibility with legacy DV components. Power Management : D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification Number of ports: * FWB-PCI3203: Two External Bilingual Ports (with screw lock) + One Internal Bilingual Port Bus Power Connector: Big IDE 4-pin DC Power Connector Operating System Requirements * The 1394b function (host driver) is supported (built in) by the following OS: o Windows 2000 SP4 or later o Windows XP SP2 or later o Windows Vista SP1 or later o Mac OS 10.4 or later o Linux kernel 2.6.23 or later. Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "